Metal nanoparticles decorated mint-cellulose acetate composite as an efficient catalyst for the reduction of methyl orange.

Water contamination caused by toxic compounds has emerged as one of the most severe challenges worldwide. Biomass-based nanocomposites offer a sustainable and renewable alternative to conventional materials. In this study, a nanocomposite of mint cellulose acetate (Mint-CA) was prepared and employed as a supportive material for Cu and Ag nanoparticles. The selectivity of CuNPs@mint-CA and AgNPs@mint-CA was assessed by comparing their performance in the reduction of various dye solutions. AgNPs@mint-CA exhibited superior catalytic performance, with a removal rate of 95.2 % for methyl orange (MO) compared to 68 % with CuNPs@mint-CA. The adsorption spectra of MO exhibit a distinct peak at 464 nm. The reduction reaction of MO by AgNPs@mint-CA followed pseudo-first-order-kinetic with a rate constant (k = 0.0046 min-1, R2 = 0.814). The highest removal of MO was achieved under the following conditions: a catalyst weight of 40 mg, an initial MO concentration of 0.07 mM, the addition of 0.5 mL of NaBH4, and a room temperature of 25 °C. Furthermore, the AgNPs@mint-CA catalyst exhibited exceptional reducibility even after five use cycles, highlighting its potential for efficiently removing MO.

Development of Poly(vinyl alcohol)-Chitosan Composite Nanofibers for Dual Drug Therapy of Wounds.

Current trends in localized drug delivery are emphasizing the development of dual drug-loaded electrospun nanofibers (NFs) for an improved therapeutic effect on wounds, especially infected skin wounds. The objective of this study was to formulate a new healing therapy for an infected skin wound. To achieve this goal, this study involved the development and characterization of poly(vinyl alcohol) (PVA)/chitosan nanofibers loaded with ciprofloxacin and rutin hydrate. Polymers and drugs were used in different ratios. Nanofiber morphology was studied by scanning electron microscopy, thermal stability by thermogravimetric analysis, structural determination by the X-ray diffraction method, and integrity by Fourier transform infrared spectroscopy. Dissolution studies were performed to check the drug release behavior of the formulations. Antibacterial studies were performed against Staphylococcus aureus and Pseudomonas aeruginosa. The wound healing efficiency of dual drug-loaded nanofibers was measured by a full-thickness excisional wound model of rabbits. The fabricated nanofibers were smooth in morphology. According to FTIR findings, the drugs remained intact in the nanofibers. The results of swelling ratio and porosity revealed that the pore size was increased as the amount of chitosan was increased up to 30% but a further increase in chitosan concentration reduced the swelling ratio and porosity. Drug release studies of nanofibers depicted an initial burst effect and afterward controlled drug release behavior. Drug-loaded nanofibers showed better activity against S. aureus than P. aeruginosa. The antibacterial efficacy of rutin hydrate with ciprofloxacin was improved compared to that of the formulation having rutin hydrate only, likely due to the additive effect in activity. Based on wound healing studies, nanofibrous membranes acted as a promising wound dressing material as compared to the commercial wound healing formulation. Drug-loaded polymeric nanofibers were successfully fabricated by using an electrospinning method. These nanofibers showed an efficient ability to deliver drugs and treat infected wounds.

Silver oxide doped iron oxide/alginate nanocomposite coated cotton cloth for selective catalytic reduction of potassium ferricyanide.

Silver oxide doped iron oxide (Ag2O-Fe2O3) nanocatalyst was prepared and coated on cotton cloth (CC) as well as wrapped in sodium alginate (Alg) hydrogel. Ag2O-Fe2O3 coated CC (Ag2O-Fe2O3/CC) and Ag2O-Fe2O3 wrapped Alg (Ag2O-Fe2O3/Alg) were utilized as catalysts in reduction reaction of 4-nitrophenol (4-NP), congo red (CR), methylene blue (MB) and potassium ferricyanide (K3[Fe(CN)6]). Ag2O-Fe2O3/CC and Ag2O-Fe2O3/Alg were found to be effective and selective catalyst for the reaction of K3[Fe(CN)6]. Further amount of catalyst, K3[Fe(CN)6] quantity, amount of NaBH4, stability of catalyst and recyclability were optimized for the reaction of K3[Fe(CN)6] reduction. Ag2O-Fe2O3/Alg and Ag2O-Fe2O3/CC were appeared to be the stable catalysts by maintaining high activity during recyclability tests showing highest reaction rate constants (kapp) of 0.3472 and 0.5629 min-1, correspondingly. However, Ag2O-Fe2O3/CC can be easily recovered as compared to Ag2O-Fe2O3/Alg by simply removing from the reaction which is the main advantage of Ag2O-Fe2O3/CC. Moreover, Ag2O-Fe2O3/Alg and Ag2O-Fe2O3/CC were also examined in real samples and found useful for K3[Fe(CN)6] reduction involving real samples. The Ag2O-Fe2O3/CC nanocatalyst is a cost and time saving material for economical reduction of K3[Fe(CN)6] and environmental safety.

A bibliometric analysis of the role of nanotechnology in dark fermentative biohydrogen production.

Recently, nanoparticles have drawn a lot of interest as catalysts to enhance the effectiveness and output of biohydrogen generation processes. This review article provides a comprehensive bibliometric analysis of the significance of nanotechnology in dark fermentative biohydrogen production. The study examines the scientific literature from the database of The Web of Science© while the bibliometric investigation utilized VOSviewer© and Bibliometrix software tools to conduct the analysis. The findings revealed that a total of 232 articles focused on studying dark fermentation for hydrogen production throughout the entire duration. The extracted data was used to analyze publication trends, authorship patterns, and geographic distribution along with types and effects of nanoparticles on the microbial community responsible for dark fermentative biohydrogen production. The findings of this bibliometric analysis provide valuable insights into the advancements and achievements in the utilization of nanoparticles in the dark fermentation process used to produce biohydrogen.

A Comprehensive Physiologically Based Pharmacokinetic Model of Nadolol in Adults with Renal Disease and Pediatrics with Supraventricular Tachycardia.

Nadolol is a long-acting non-selective ß-adrenergic antagonist that helps treat angina and hypertension. The current study aimed to develop and validate the physiologically based pharmacokinetic model (PBPK) of nadolol in healthy adults, renal-compromised, and pediatric populations. A comprehensive PBPK model was established by utilizing a PK-Sim simulator. After establishing and validating the model in healthy adults, pathophysiological changes i.e., blood flow, hematocrit, and GFR that occur in renal failure were incorporated in the developed model, and the drug exposure was assessed through Box plots. The pediatric model was also developed and evaluated by considering the renal maturation process. The validation of the models was carried out by visual predictive checks, calculating predicted to observed (Rpre/obs) and the average fold error (AFE) of PK parameters i.e., the area under the concentration-time curve (AUC0-t), the maximum concentration in plasma (Cmax), and CL (clearance). The presented PBPK model successfully simulates the nadolol PK in healthy adults, renal-impaired, and pediatric populations, as the Rpre/obs values of all PK parameters fall within the acceptable range. The established PBPK model can be useful in nadolol dose optimization in patients with renal failure and children with supraventricular tachycardia.

Smart colorimetric indicator films prepared from chitosan and polyvinyl alcohol with high mechanical strength and hydrophobic properties for monitoring shrimp freshness.

This work aimed to develop and characterize a colorimetric indicator films based on chitosan (CS), polyvinyl alcohol (PVA), and shikonin (SKN) from radix Lithospermi by casting method. The prepared films can serve as smart packaging for monitoring shrimp freshness which having excellent antimicrobial and antioxidant activity. The shikonin containing films have better hydrophobicity, barrier properties, and tensile strength. The release kinetics analysis shows that the loading amount causes a prolonged release of SKN from the prepared films. Increasing SKN in the CS/PVA film from 1 wt% to 2 wt% improved antibacterial effect for 24 h. Additionally, pH-sensitive color shifts from reddish (pH 2) to purple-bluish (pH 13) were visually seen in shikonin based solutions as well as films. The CS/PVA/SKN film detected shrimp deterioration at three temperatures (25, -20, and 4 °C) through color change. This study introduces a favorable approach for smart packaging in the food industry using multifunctional films.

Profile of contact lens prescribing in GCC countries.

PURPOSE: This study aimed to report the pattern of contact lens prescribing from the Gulf Cooperation Council (GCC) countries. METHODS: Optometrists in the GCC region were contacted to participate in a web-based survey hosted on Qualtrics XM (Provo, Utah, USA). The survey methodology was adapted from the International Contact Lens Prescribing Consortium, and participants were asked to report their last five lens fits. It collected information on practitioner demographics (age, gender, nationality, qualification, country of practice, and number of years of experience), CL user demographics (age and gender) and on lens specific details such as lens type, lens design, lens material, replacement plan, and modality of lens wear. Descriptive statistics were used to analyse and report the data. RESULTS: This study reports 739 contact lens fits by 174 practitioners from six GCC countries. The average age of the patients was 29.72 ± 9.07 (Mean ± SD) years and 64 % of them were females. The majority (80.2 %) were fitted with soft contact lenses, with 59 % preferring silicone hydrogels, 20 % wearing them for cosmetic purposes and nearly half of them disposed of their lenses daily (55 %). Among the RGP lenses, 41 % were scleral lenses. This survey demonstrated a greater proportion of new lens fits (55 % vs. 37 %), disposable hydrogel lens use (21 % vs. 13 %), and a preference for cosmetic contact lenses (20 % vs. 4 %) compared to the international data. CONCLUSION: The pattern of CL prescriptions in the GCC region closely resembled the global trend. The survey observed a higher preference towards frequent replacement soft lenses, a greater proportion of silicone hydrogel lenses, a higher percentage of rigid lens fits, a greater affinity for cosmetic contact lenses, and a higher percentage of new fits. These trends suggest that contact lens prescription habits in the region are likely to continue evolving in the future.

Biodesulfurization of organosulfur compounds by a trehalose biosurfactant producing Gordonia sp. isolated from crude oil contaminated soil.

Certain factors hinder the commercialization of biodesulfurization process, including low substrate-specificity of the currently reported desulfurizing bacteria and restricted mass transfer of organic-sulfur compounds in biphasic systems. These obstacles must be addressed to clean organic-sulfur rich petro-fuels that pose serious environmental and health challenges. In current study, a dibenzothiophene desulfurizing strain, Gordonia rubripertincta W3S5 (source: oil contaminated soil) was systematically evaluated for its potential to remove sulfur from individual compounds and mixture of organic-sulfur compounds. Metabolic and genetic analyses confirmed that strain W3S5 desulfurized dibenzothiophene to 2-hydroxybiphenyl, suggesting that it follows the sulfur specific 4 S pathway. Furthermore, this strain demonstrated the ability to produce trehalose biosurfactants (with an EI24 of 53%) in the presence of dibenzothiophene, as confirmed by TLC and FTIR analyses. Various genome annotation tools, such as ClassicRAST, BlastKOALA, BV-BRC, and NCBI-PGAP, predicted the presence of otsA, otsB, treY, treZ, treP, and Trehalose-monomycolate lipid synthesis genes in the genomic pool of strain W3S5, confirming the existence of the OtsAB, TreYZ, and TreP pathways. Overall, these results underscore the potential of strain W3S5 as a valuable candidate for enhancing desulfurization efficiency and addressing the mass transfer challenges essential for achieving a scaled-up scenario.

Measurement of Head Circumference Using a Smartphone: Feasibility Cohort Study.

BACKGROUND: Accurate head circumference (HC) measurement is essential when assessing neonates and infants. Tape measure HC measurements are prone to errors, particularly when performed by parents/guardians, due to individual differences in head shape, hair style and texture, subject cooperation, and examiner techniques, including tape measure placement and tautness. There is, therefore, the need for a more reliable method. OBJECTIVE: The primary objective of this study was to evaluate the validity, reliability, and consistency of HC app measurement compared to the current standard of practice, serving as a proof-of-concept for use by health care professionals. METHODS: We recruited infants attending the neurosurgery clinic, and parents/guardians were approached and consented to participate in the study. Along with the standard head circumference measurement, measurements were taken with the head circumference app (HC app) developed in-house, and we also collected baseline medical history and characteristics. For the statistical analysis, we used RStudio (version 4.1.1). In summary, we analyzed covariance and intraclass correlation coefficient (ICC) to compare the measurement's within-rater and interrater reliability. The F test was used to analyze the variance between measurements and the Bland-Altman agreement, t test, and correlation coefficients were used to compare the tape measurement to the measures taken by the HC app. We also used nonvalidated questionnaires to explore parental or guardians' experiences, assess their views on app utility, and collect feedback. RESULTS: The total number of recruited patients was 37. Comparison between the app measurements and the measurements with a tape measure showed poor reliability (ICC=0.177) and wide within-app variations (ICC=0.341). The agreement between the measurements done by parents/guardians and the tape measurements done by the researcher was good (ICC=0.901). Parental/guardian feedback was overall very positive, with most of the parents/guardians reporting that the app was easy to use (n=31, 84%) and that they are happy to use the app in an unsupervised setting, provided that they are assured of the measurement quality. CONCLUSIONS: We developed this project as a proof-of-concept study, and as such, the app has shown great potential to be used both in a clinical setting and by parents/guardians in their own homes.

Smoke-water obtained via different biotics: a cost-effective and safer approach to biochemically sound banana ripening with prolonged shelf-life.

This study was conducted to investigate the efficacy of smoke-water obtained from biotics, for example coconut shells, rice husk, and pine cones on banana ripening, and compared with calcium carbide. Bio-chemical composition and remarkable bactericidal effect towards ATCC cultures of Escherichia coli, Staphylococcus aureus, and Bacillus cereus discovered the biological safety of the smoke-water in all collected smoke-water samples. Further, inductively coupled plasma mass spectrometry (ICP-MS) was carried out to investigate heavy metals; however, no traces were found in all collected samples. Consequently, it is proposed that heavy metal-free smoke-water obtained from various biotics series might be employed as ultrasafe fruit ripening as compared to calcium carbide (CaC2) that was found with heavy metal traces.

Comment on "renal denervation for hypertension".

We have attentively reviewed the article "Renal Denervation for Hypertension" and commend the author's dedication to addressing this intricate subject. However, we wish to highlight a few points that, in our assessment, could enhance the overall quality of the article.

Mitigation of sciatica injury-induced neuropathic pain through active metabolites derived from medicinal plants.

Sciatica characterized by irritation, inflammation, and compression of the lower back nerve, is considered one of the most common back ailments globally. Currently, the therapeutic regimens for sciatica are experiencing a paradigm shift from the conventional pharmacological approach toward exploring potent phytochemicals from medicinal plants. There is a dire need to identify novel phytochemicals with anti-neuropathic potential. This review aimed to identify the potent phytochemicals from diverse medicinal plants capable of alleviating neuropathic pain associated with sciatica. This review describes the pathophysiology of sciatic nerve pain, its cellular mechanisms, and the pharmacological potential of various plants and phytochemicals using animal-based models of sciatic nerve injury-induced pain. Extensive searches across databases such as Medline, PubMed, Web of Science, Scopus, ScienceDirect, and Google Scholar were conducted. The findings highlights 39 families including Lamiaceae, Asteraceae, Fabaceae, and Apocyanaceae and Cucurbitaceae, effectively treating sciatic nerve injury-induced pain. Flavonoids made up 53% constituents, phenols and terpenoids made up 15%, alkaloids made up 13%, and glycosides made up 6% to be used in neuorpathic pain. Phytochemicals derived from various medicinal plants can serve as potential therapeutic targets for both acute and chronic sciatic injury-induced neuropathic pain.

Polymeric coating doped with nanomaterials for functional impact on different substrates.

Microorganism contamination on substrate surfaces is arousing increasingly concern as a serious health issue. In this research work, antimicrobial water-based acrylic paint containing silver nanoparticles (Ag NPs) was prepared using the facile Ag+ in situ reduction process, in which AgNO3 and reducing agent sodium acrylate were refluxed with acrylic polymeric solution to obtain an antimicrobial and antifungal polymeric material for substrate coating. The Synthesized antimicrobial and antifungal water-based acrylic paint were characterized by different spectroscopic techniques. The FTIR and UV-Visible spectroscopic analyses were investigated to study the water-based acrylic paint structure as well as the significant impact of Ag NPs on the paint matrix. The UV-Visible and FTIR Spectra peak shows successful integration of Ag NPs within the polymer matrix without altering the core functional groups of the paint. The water based acrylic paint exhibited a strong antimicrobial activity, revealed substantial inhibition zones against all four strains of Gram negative represented by Escherichia coli, Acinetobacter baumannii, Klebsiella pneumoniae and Gram-positive represented by Bacillus cereus. The coated film on substrate also shows great inhibition zone which exhibit a strong antimicrobial activity. Moreover, water based acrylic paint also exhibited a great antifungal activity, revealed substantial zone of inhibition against the Aspergillus niger, Aspergillus terreus and Rhizopus arrhizus fungal strains. Also, the coated film showed the best adhesion at 50% and 80% solution of polymeric coating sample as compared to pure or very dilute sample coating. This innovative approach has the potential to revolutionize varies industries from healthcare to construction.

Genomic analysis and biodesulfurization potential of a new carbon-sulfur bond cleaving Tsukamurella sp. 3OW.

Direct combustion of sulfur-enriched liquid fuel oil causes sulfur oxide emission, which is one of the main contributors to air pollution. Biodesulfurization is a promising and eco-friendly method to desulfurize a wide range of thiophenic compounds present in fuel oil. Previously, numerous bacterial strains from genera such as Rhodococcus, Corynebacterium, Gordonia, Nocardia, Mycobacterium, Mycolicibacterium, Paenibacillus, Shewanella, Sphingomonas, Halothiobacillus, and Bacillus have been reported to be capable of desulfurizing model thiophenic compounds or fossil fuels. In the present study, we report a new desulfurizing bacterium, Tsukamurella sp. 3OW, capable of desulfurization of dibenzothiophene through the carbon-sulfur bond cleavage 4S pathway. The bacterium showed a high affinity for the hydrocarbon phase and broad substrate specificity towards various thiophenic compounds. The overall genome-related index analysis revealed that the bacterium is closely related to Tsukamurella paurometabola species. The genomic pool of strain 3OW contains 57 genes related to sulfur metabolism, including the key dszABC genes responsible for dibenzothiophene desulfurization. The DBT-adapted cells of the strain 3OW displayed significant resilience and viability in elevated concentrations of crude oil. The bacterium showed a 19 and 37% reduction in the total sulfur present in crude and diesel oil, respectively. Furthermore, FTIR analysis indicates that the oil's overall chemistry remained unaltered following biodesulfurization. This study implies that Tsukamurella paurometabola species, previously undocumented in the context of biodesulfurization, has good potential for application in the biodesulfurization of petroleum oils.

Unveiling genetics of non-syndromic albinism using whole exome sequencing: A comprehensive study of TYR, TYRP1, OCA2 and MC1R genes in 17 families.

BACKGROUND: Oculocutaneous albinism (OCA) is a group of skin depigmentation disorders. Clinical presentation of OCA includes defects in melanocyte differentiation, melanin biosynthesis, and melanosome maturation and transport. OBJECTIVES: A molecular diagnostics study of families presenting oculocutaneous albinism. METHODS: In this study, 17 consanguineous OCA families consisting of 93 patients were investigated. Whole Exome Sequencing (WES) of the index patient in each family were performed. Short listed variants of WES were Sanger validated for Mendelian segregation in obligate carriers and other available family members. Variant prioritization and pathogenicity were classified as per the criteria of American College Medical Genetics and Genomics (ACMG). Comparative computational modelling was performed to predict the potential damaging effect of the altered proteins. RESULTS: 15 pathogenic variations: c.132 T > A, c.346C > T, c.488C > G, c.1037G > A in TYR, c.1211C > T, c.1441G > A, c.1706_1707insT, c.2020C > G, c.2402G > C, c.2430del, in OCA2, c.1067G > A in TYRP1 and c.451C > T, c.515G > T, c.766C > T, c.917G > A in MC1R genes were identified. Three variants in OCA2 gene were characterized: c.1706_1707insT, c.2430del, and c.2402G > C, all of which were not reported before in OCA families. CONCLUSION: A few studies focusing on mutation screening of OCA patients have been reported before; however, this study has uniquely presents the Pakhtun ethnic population residing on the North-Western boarder. It explains that TYR, OCA2, TYRP1, and MC1R variations lead to non-syndromic OCA phenotype The overlapping phenotypes of OCA can precisely be diagnosed for its molecular pathogenicity using WES. This study recommends WES as a first-line molecular diagnostic tool, and provides a basis for developing customized genetic tests i.e. pre-marital screening to reduce the disease burden in the future generations.

Drinking water quality of various sources in Peshawar, Mardan, Kohat and Swat districts of Khyber Pakhtunkhwa province, Pakistan / Qualidade de água potável de váris fontes dos distritos de Peshawar, Mardan, Kohat e Swat da província de Khyber Pakhtunkhwa, Paquistão

Abstract The present study involves the chemical and bacteriological analysis of water from different sources i.e., bore, wells, bottle, and tap, from Peshawar, Mardan, Swat and Kohat districts of Khyber Pakhtunkhwa (KP) province, Pakistan. From each district, 50 water samples (10 samples from each source), regardless of urban and rural status, were collected from these sources and analysed for sulphates, nitrates, nitrites, chlorides, total soluble solids and coliforms (E. coli). Results indicated that majority of the water sources had unacceptable E. coli count i.e.> 34 CFU/100mL. E. coli positive samples were high in Mardan District, followed by Kohat, Swat and Peshawar district. Besides this, the some water sources were also chemically contaminated by different inorganic fertilizers (nitrates/nitrites of sodium, potassium) but under safe levels whereas agricultural and industrial wastes (chloride and sulphate compounds) were in unsafe range. Among all districts, the water quality was found comparatively more deteriorated in Kohat and Mardan districts than Peshawar and Swat districts. Such chemically and bacteriologically unfit water sources for drinking and can cause human health problems.

Resumo O presente estudo envolve a análise química e bacteriológica de água de diferentes fontes, ou seja, furo, poços, garrafa e torneira, dos distritos de Peshawar, Mardan, Swat e Kohat da província de Khyber Pakhtunkhwa (KP), Paquistão. De cada distrito, 50 amostras de água (10 amostras de cada fonte), independentemente do status urbano e rural, foram coletadas dessas fontes e analisadas para sulfatos, nitratos, nitritos, cloretos, sólidos solúveis totais e coliformes (E. coli). Os resultados indicaram que a maioria das fontes de água tinha uma contagem inaceitável de E. coli, ou seja, > 34 UFC / 100 mL. As amostras positivas para E. coli foram elevadas no distrito de Mardan, seguido por Kohat, Swat e distrito de Peshawar. Além disso, algumas fontes de água também foram contaminadas quimicamente por diferentes fertilizantes inorgânicos (nitratos/nitritos de sódio, potássio), mas em níveis seguros, enquanto os resíduos agrícolas e industriais (compostos de cloreto e sulfato) estavam em níveis inseguros. Entre todos os distritos, a qualidade da água foi considerada comparativamente mais deteriorada nos distritos de Kohat e Mardan do que nos distritos de Peshawar e Swat. Essas fontes de água química e bacteriologicamente impróprias para beber podem causar problemas à saúde humana.

Drinking water quality of various sources in Peshawar, Mardan, Kohat and Swat districts of Khyber Pakhtunkhwa province, Pakistan

Abstract The present study involves the chemical and bacteriological analysis of water from different sources i.e., bore, wells, bottle, and tap, from Peshawar, Mardan, Swat and Kohat districts of Khyber Pakhtunkhwa (KP) province, Pakistan. From each district, 50 water samples (10 samples from each source), regardless of urban and rural status, were collected from these sources and analysed for sulphates, nitrates, nitrites, chlorides, total soluble solids and coliforms (E. coli). Results indicated that majority of the water sources had unacceptable E. coli count i.e.> 34 CFU/100mL. E. coli positive samples were high in Mardan District, followed by Kohat, Swat and Peshawar district. Besides this, the some water sources were also chemically contaminated by different inorganic fertilizers (nitrates/nitrites of sodium, potassium) but under safe levels whereas agricultural and industrial wastes (chloride and sulphate compounds) were in unsafe range. Among all districts, the water quality was found comparatively more deteriorated in Kohat and Mardan districts than Peshawar and Swat districts. Such chemically and bacteriologically unfit water sources for drinking and can cause human health problems.

Resumo O presente estudo envolve a análise química e bacteriológica de água de diferentes fontes, ou seja, furo, poços, garrafa e torneira, dos distritos de Peshawar, Mardan, Swat e Kohat da província de Khyber Pakhtunkhwa (KP), Paquistão. De cada distrito, 50 amostras de água (10 amostras de cada fonte), independentemente do status urbano e rural, foram coletadas dessas fontes e analisadas para sulfatos, nitratos, nitritos, cloretos, sólidos solúveis totais e coliformes (E. coli). Os resultados indicaram que a maioria das fontes de água tinha uma contagem inaceitável de E. coli, ou seja, > 34 UFC / 100 mL. As amostras positivas para E. coli foram elevadas no distrito de Mardan, seguido por Kohat, Swat e distrito de Peshawar. Além disso, algumas fontes de água também foram contaminadas quimicamente por diferentes fertilizantes inorgânicos (nitratos/nitritos de sódio, potássio), mas em níveis seguros, enquanto os resíduos agrícolas e industriais (compostos de cloreto e sulfato) estavam em níveis inseguros. Entre todos os distritos, a qualidade da água foi considerada comparativamente mais deteriorada nos distritos de Kohat e Mardan do que nos distritos de Peshawar e Swat. Essas fontes de água química e bacteriologicamente impróprias para beber podem causar problemas à saúde humana.

Assessment and computational bioevaluation of heavy metals from selected cosmetic products.

Heavy metal toxicity in environment has been an increasing issue for last decades, though now the attention has diverted to presence of heavy metals in cosmetic products. The aim of this study was to determine the concentration of selected heavy metals in cosmetic products (lipsticks and foundations) using ICP-OES. Health risk assessment was done by using hazard quotient (HQ) and hazard index (HI). HQ for lipsticks was below the safe limit (HQ = < 1) while for foundations it exceeded the safe limit (HQ = >1). Mostly, mercury (Hg) and iron (Fe) were found to be exceeding the permissible limit, the allowed limits are Hg, 1 ppm; Fe, 10 ppm; Cd, 0.3 ppm; and Cr, 1 ppm. Iron was found to be highest in lipsticks (123.86 ± 1.05 ppm) as well as in foundations (34.52 ± 0.08 ppm). Health risk assessment was done by using hazard quotient (HQ) and hazard index (HI). HQ for lipsticks was below the safe limit (HQ = < 1) while for foundations it exceeded the safe limit (HQ = >1). To understand the binding pattern of heavy metals to skin targets, molecular docking studies were carried out. This revealed the potentially harmful behavior of these heavy metals on the skin. This will provide new direction for the structural changes of consistence and activity of macromolecules in our body. Research proved that prolonged use of cosmetic products containing heavy metals can be harmful and sometimes fatal to human life as these heavy metals can penetrate through the skin and target the skin enzymes, disrupting their normal function leading to various skin related issues such as dermatitis (itching, redness, burning) hence the monitoring of cosmetic products is necessary for safety of human being.

Exercise induced muscle weakness in a young adult: McArdle's disease unusual presentation.

McArdle's disease (Glycogen storage disease type V) is a rare inherited autosomal recessive disease involving defect in enzyme, glycogen phosphorylase (PYGM) which results in accumulation of glycogen mainly affecting skeletal muscles. It commonly presents in childhood and rarely in adults with symptoms like exercise intolerance, muscle weakness, cramps and fatigue. Herein, we report an unusual case of a 22 years old male in Pakistan with probable McArdle's Disease presenting with repeated episodes of generalized cramping muscle pain, exercise intolerance and haematuria. The diagnostic approach to identifying this disease as well as the differentials of other rare types of skeletal muscle disorders that should be kept in mind while dealing with a similar clinical picture, irrespective of the age of presentation, have been discussed.